Y132m-4 Variable Speed Motor Driving Force Milling Machine

Y132m-4 Variable Speed Motor Driving Force Milling Machine

Y132M-4 variable velocity motor driving pressure milling equipment
one basic operation, large performance!
2 with simple upkeep, power, simple to go and so on
three to eliminate the ground coating, paint, a selection of street marking
4 broken ground, the want for renovation of the plot, get rid of the old floor floor
five into the quality of heaven and earth, provide limitless organization chances

scarifying equipment is a mild motor drive ground milling device to 7.5kw kilowatts Y132M-4 variable speed motor as the driving drive, the use of CZPT chopping the doing work basic principle, can rapidly reduce the ground material! Functioning basic principle: Unlike the massive-scale milling machine’s anti-chopping principle, the little milling machine relies on the constructive high-speed rotation of the milling drum, so as to shake the six groups of hard tungsten steel alloy blades on the milling cutter shaft. , The use of alloy blade on the tungsten steel alloy enamel to crack and floor the floor material, so as to achieve the effect of surface milling

concrete scarifier device Mainly employed for highway, city streets, airports, freight lawn and other asphalt concrete floor of the excavation renovation, can also be utilized to eliminate the road package deal, oil waves, textures, rutting and other flaws can also be utilised to excavate pits and ditch Groove, and the cement road floor of the hair and the floor of the wrong amount of milling.


CZPT venture product:WC-200G product WC-255G
Electrical power configuration Three-phase asynchronous motor / five.5KW (CW200D)
Honda GX270 Gasoline Motor / 13HP (WC200F)
A few-stage asynchronous motor / 7.5KW (CW255D)
Honda GX270 Gasoline Engine / 13HP (WC255F)
Variety of knife shafts 6 root 6 root
Quantity of blades 78 pieces (6 tooth) 108 parts (6 enamel)
CZPT seal type Sealed (routine maintenance-free) Sealed (servicing-free)
A milling width 200mm 250mm
A milling depth 3mm-5mm 3mm-5mm
excess weight 90kg 115kg
Extended × vast × high 1125×500×1125mm 1125×500×1125mm
Hourly perform efficiency 150 square 170 square
Strolling wheel 4 only 4 only
Air damping tube 2 only 2pc
Counterweight   25kg(common)

4. concrete scarifier device use and maintenance
1 device is the major component of the operate owing to milling cutter, bearings, gaskets, milling drums, the procedure approach due to a long time with the street friction, the swiftest use is this portion of the typical alternative, inspection in purchase to far better extend the use of the device life
two, milling cutter shaft ought to be checked every day, if the previously mentioned grinding out of the slot far more than twenty five% of the diameter of the knife, you have to exchange. In general, the existence of the knife shaft is fifty percent the daily life of the tungsten metal cutter. scarifying machine From the sq. spot, the existence of the milling depth of 5mm when about 350-five hundred square meters. But you should pay interest to, there are many factors that will influence the lifestyle of the knife shaft, so to verify each working day
3, for basic safety factors, before the routine maintenance, must very first pull the engine spark plug, preferably by the qualified mechanic
four, every time ahead of running to check the oil degree, right after use to clean the air filter
five, every 4 hrs right after use, to grease the bearing. concrete scarifier Hit the grease, although actively playing side of the rotation drum, so that grease coated in the whole bearing
6, before every single procedure with the bare eye to check the machine: all fasteners are tightened? Are there any parts of the apparent use or cracking? Oil pipeline is intact? Check out the bearings, check out the protect is coated
seven, ahead of each procedure, to verify the belt tightness. The new belt should be reoriented following four hrs of operation, and the belt tension need to be taken care of in purchase to transmit the output horsepower of the motor to the cutter drum. scarifier concrete grinder When the tight belt is too restricted, the belt will be simply worn and the bearing daily life will be shortened , If broken, severe use and tear of the belt need to immediately change the new fail to remember the earlier to have a new start. 
8, in basic, milling cutter cracking is really rare, if any, generally exhibits the following: a: milling cutter on the irregular arrangement b: a one milling also deep c: the use of inappropriate milling Knife to eliminate the distinct sorts of road d: milling the surface area energy is way too large to be bravery to confess their errors, and bear the obligation.
9, each time you adjust the milling cutter arrangement, examine the cutter shaft and the bearing. If the shaft appears to use the groove, you want to exchange the new, when the axis for the identical time for bearings
ten, milling drum if appropriately maintained, normally can be utilized for three months. When checking the milling cutter or doing maintenance, examine whether or not there is any cracks in the centre axis of the milling drum, no matter whether the sleeve hole is oval, whether or not there is any crack at the weld, and if there is any hurt,
eleven, and ultimately, when you want to check the milling equipment at the bottom of the milling equipment, reminded that: the equipment have to be tilted CZPT, by no means backward, or oil will pour into the engine cylinder.

Model ZT70 ZT100 ZT120
Drill Diamter φ60-80mm φ83-100mm φ85~130mm
Rock hardness ≥20 ≥20 ≥20
Drill Depth ≥15m ≥30 30-40m
Swing velocity 110r/min 90r/min 90r/min
Air strain .5-.7Mpa .5-.7Mpa .5~one.0Mpa
Air consumption ≥3.5m3/min 6M3/min 10m3/min
Cylinder Diameter 90mm 90mm 90mm
Valid Length 1070mm 1070mm 1200mm
Propulsion 3600N 6000N 9600N
Energy 3kW 3kW 3kW
Voltage 380V 380V 380V
Rated pace 1410r/min 1410r/min 1410r/min
Outer Diameter φ42mm φ42mm φ42mm
Drill Pipe Size 1571mm 1571mm 1571mm
Measurement 1740×260×420mm 1800*650*400mm 1800*seven hundred*450mm
Bodyweight 220kg 250kg 300kg 

Q1: Are you factory or trade firm?
A1: We are manufacturing facility. And we have ourselves investing firm.
Q2: What the exactly address of your manufacturing facility?
A2:  No.27,Xihu (West Lake) Dis. Village CZPT Park, Xihu (West Lake) Dis. District, ZheJiang Province China.                                                                                                                            
Q3: Warranty terms of your device?
A3: One yr guarantee for the device and complex assistance in accordance to your demands.

This fall: Will you offer some spare parts of the machines?
A4: Of course, of training course.

Q5: What about the voltage of merchandise? Can they be CZPT?
A5: Our regular voltage is 380V, 50HZ, 3phase. The voltage can be CZPT in accordance to your equirement.
Q6: Which payment time period can you take?
A6: one hundred% T/T( Decide in accordance to true situation)

Q7: How lengthy will you consider to set up production?
A7: we can shipping and delivery the standard products within 7-fifteen days. Other nonstandard electrical objects we will delivery inside 25-thirty days.
Q8: Can you take OEM orders?
A8: Of course, with skilled design team, OEM orders are highly welcome.
Q9: Which trade phrase can you settle for?
A9: Available trade conditions: FOB, CIF, CFR, EXW, etc.

Q10: Do you give samples? Is it totally free or further?
A10: Indeed, we could supply you the sample device. But it really is not cost-free. You want to shell out for the sample and the value of freight.

Q11: What is your terms of payment?
A11: We accept T/T, Western Union, Money Gram, Paypal, L/C, and so forth.
Our Company Information:

We have been focusing on substantial-high quality mechanical products and building merchandise for a lot more than 20 many years. Especially have abundant experience at mining tools, primary items consist of:

Ultra Massive Rock Splitter
Submersible Drilling Rig
Spraying Machine
Grinding Equipment

About Our Manufacturing facility:

About the products:

Packing and Shipping and delivery:

Obtain Procedure:

About the High quality:

Other individuals:

Why you decide on us:

1. We are a real factory providing items and provide free of charge technological tips.
two. Company in enterprise for many many years and served Above fifty nations buyers.
3. All device with CE, ISO,SGS certificate. Machine and spindle warranty 1 year. 
4. We have mobile phone assistance in English, if you have any concerns, you can get in touch with us, and we can give you the best remedy inside of 24 several hours.
five. Quick shipping, help save your time. 

Make contact with us:


Y132m-4 Variable Speed Motor Driving Force Milling Machine